Search Results for: diy

DIY Copper Coffee Table

Kate-Miss-CopperTable

It all started with getting a real sofa. And then I made a coffee table that wasn’t great, but we didn’t hang out on the sofa often so we didn’t really notice that much. But then we got a TV and suddenly a good coffee table was much more important. Something to prop your feet on, something to hold all the damn remotes a TV requires, something to put your glass of wine on while you plow through seven episodes of Scandal in a row. So we built another not great coffee table, constructed of things we already had, and it turned out to be awful and wobbly. Will is a carpenter but building things when he gets home after hours of hard labor does not sound appealing, and I get that.

Kate-Miss-CopperTable-2

So I started plotting something on my own, something to do on the side as I’ve been in need of a non-work related project. After I built a copper pipe jewelry stand for the book fair, I decided I really wanted to use copper pipe. Pros: so pretty! You can cut it yourself fairly easily! They sell everything you need at Home Depot! Cons: so expensive, they don’t really make flanges for it so you have to get creative with how it attaches to things and connects. I sketched out a million ideas and almost gave up until an idea sprang into my head so suddenly I immediately jumped from my desk and ran to Home Depot.

Kate-Miss-CopperTable-4Kate-Miss-CopperTable-3

Ok, so if you’ve ever spontaneously built something before you know it’s not always the best idea to spring from your desk and run to the hardware store. So it’s no wonder I returned to the hardware store three times in less than 8 hours and went over budget accidentally cutting copper incorrect lengths. But I finally did it, and did it all on my own. Carpenter husband gave it his seal of approval. I will admit it’s not perfect and because cutting copper isn’t super precise the legs aren’t 100% even so I need some rubber on the bottom to even it out, but it’s nothing crazy.

Kate-Miss-CopperTable-5Kate-Miss-CopperTable-quad

Here’s what you need for this project (I’m linking to Home Depot as that’s where I bought everything, I’m not sure what other hardware stores will have):

  • 1/2″ Type M Copper Pipe. Type M is the softest and cheapest and all you need for this since we’re not building a house. The longer the piece of copper you buy, the more you will save, but you have to have the means to transport it. I could only fit 5′ pipes in my car, but they also sell 10′ if you have a larger vehicle, and that is the more economical route.
    My table’s wood top is 4ft long by 17″ wide and 1″ thick. It stands about 16.5″ tall and I wish it was only 16″ as my sofa is so low, but it’s not obnoxious to use, it just looks a tad too high. Here’s a break down of the pipe sizes you’ll need to cut for this particular size:
    6 at 14″ – these are you legs
    3 (edited from six, which was incorrect earlier, sorry!) at 13 1/4″ – these connect the legs on the floor
    4 at 22.5″ (this caused my pipe to be flush with the edge of my wood, which is dangerous as it could look dumb if it wasn’t exact and stuck out, I might recommend doing 22 or 22.25″ to be safe) – these connect all the pieces together and get drilled against the wood.
  • 10 1/2″ CxC 90 Degree Angle Elbows. MAKE SURE you are buying CxC and that your copper pipe fits into both ends. The first trip I bought one that fit into one end but not the other. d’oh.
  • 2 1/2″ Tees. Make sure all three ends are 1/2″.
  • 6 1/2″ Tube Straps. Because they come in packs of 5, you could go crazy and screw down the pipe in more spots if you’re paranoid.
  • Wood board. I used a 4ft long by 17″ wide and 1″ thick piece of laminated pine. It’s actually the exact same piece I made my old desk with ages ago and I highly suggest a piece this thick as it has less of a chance of bowing and holds everything nicely.
  • Wood stain. I used a stain + poly to protect spills and cup rings but applied it quite light as I hate the look of thick poly. (optional, I think a raw piece of wood would also look awesome, though I might recommend sealing it if you have an ounce of slob in you like myself) You’ll obviously also need all the stuff to stain it. Gloves, sandpaper to prep the wood and sand in between coats, your brush of choice (I like foam). TIP: stain both sides! The wood will bow if you do not.
  • 12 3/4″ wood screws. When you drill one side down you can pull the other a bit to line it up evenly, don’t be discouraged if you lay it on top of the wood and it looks warped.
  • Gorilla glue. Copper connections meant to be soldered together for a tight fit and this does the job instead and makes the whole thing tight and not so wobbly. I only glued the leg pieces, so I assembled everything, drilled it all down, and then removed all the leg pieces and glued them, then flipped the table right side up to let it dry with weight on it. A rubber mallet is helpful for making sure everything is snug.
  • Pipe cutter. Make sure it cuts copper. Pro tip: Don’t buy the cheap junior one! I bought the cheap one and it cut in a spiral and gave me blisters. I went back and bought the more expensive one and it not only cut straighter, but was less insane on my poor hands. But it still may cut in a spiral sometimes. If so, rotate at 180 degrees back and forth instead of around and around.

In the end I spent about $160, though I wasted some copper cutting a whole pipe the wrong length, so it could be a touch lower for you, and you may have things around like screws, stain, glue, etc. Even though it was a lot of work, it looks so much better than something I could have purchased for twice that! Also, something to note is the copper will oxidize over time and get darker, especially if you touch it often. You could coat it with a protective finish, which I’m contemplating. I’ll update you on that if I decide to, though I think spray polycrylic would be best?

Because I know someone may ask, my living room details: sofa – vintage, pillows: Barrington Blue and Cotton & Flax, rug: Overstock.com (though I’m so tired of it and want a new one! Who wants to buy me this one or this one?), curtains: Target (they’re ombre though it’s hard to tell), lamp: CB2, everything else is vintage.

Recent DIYs

I’ve been getting crafty on a budget lately with some DIYs.


Vintage spoons + paint + leather ties = simple, easy art above my sink.


An old shirt from H&M made new again with fabric dye. The mottled look comes from the fabric not being 100% cotton and the dye not taking to it completely, no fancy moves made to achieve it.


Flea market side dressers (there’s another one on the other side of the bed) sanded, stained and handles replaced (they’re a nice brass but the light was so awful they’re looking silver here). Because y’all are predictable with your questions, the lamp is from West Elm and the bedding is DwellStudio.

DIY Dining Table

After completing my first DIY desk using hairpin legs, I instantly dreamed about making a round dining table. I had to wait months until we moved, but I never stopped daydreaming about how perfect it would be, and even started buying supplies before we moved into the new place. Ian of hairpinlegs.com generously offered to send me some legs to make my day dreaming come true, and I was floored by his kindness. The legs came, just as beautiful and perfect as the last set, and I had to agonizingly wait to build the table while the stress of moving set in and plans were foiled week and after week. But alas! It’s finished, and it’s amazing.

I followed the same steps as last time, but this time practiced a little thing called patience and actually followed directions while staining – sand, stain, wait overnight, sand, stain again. Wait. Wait. Wait. Attach legs. Then of course the screws I had were too long and the thought of going back to the hardware store and waiting YET AGAIN destroyed me, so I just used bolts. You can see them from certain angles, but it doesn’t bother me one bit.

Then last week I found some fantastic vintage chairs for crazy, crazy cheap on craigslist and met a wonderful woman to pick them up and found out she has an Etsy shop and also sells at the Melrose Flea Market. How often do you meet cool, sane people off of craigslist? I have the most terrible craigslist luck and never find anything cool, so I was excited. The upholstery is in need of an upgrade, and seeing as my family owns an upholstery shop I think I can somehow swing that one of these days. We also have these amazing industrial metal pendant lamps that I really wanted to hang over the table, but those plans were ruined after we discovered that our ceiling is made of cake or something because no amount of trickery will get a screw to stay in that baby. Sad face.

Despite crushed lamp dreams and that semi-fug sage green wall I need to repaint soon (thinking a warm grey), I’m pretty excited about the dining area. It’s small, but cozy and perfect for two.

Details:
Round wood, 36″: Fisher (this was tough to track down! It was about $20)
Hairpin legs, 28″ 3-rod raw steel: hairpinlegs.com
Stain: Minwax PolyShades in Antique Walnut